- 您现在的位置：买卖IC网 > Sheet目录303 > 844USB (B&K Precision)DEVICE PROGRAMMER USB INTERFACE
Supply voltage (in mV) - supply voltage in target system. Control program checks or sets (it
depends on programmer type) entered supply voltage in target system before every action on
device.
Disable test supply voltage - disables measure and checking supply voltage of
programmed device, set in Supply voltage edit box, before action with device.
Delay after reset active - this parameter determine delay after Reset signal active to start
action with device. This delay depends on values of used devices in reset circuit of device
and can be chosen from these values: 10ms, 50ms, 100ms, 500ms or 1s.
I nactive level of ISP signals - this parameter determine level of ISP signals after finishing
access to target device. Signals of ISP connector can be set to Pull-up (signals are tied
through 22k resistors to supply voltage) or Pull-down (signals are tied through 22k resistors to
ground).
Keep ISP signals at defined level after operation - enables keeping set level of ISP signals
after access to target device finished. Control program indicates activated pull-up/pull-down
resistors by displaying window with warning. After user close this window control program will
deactivate resistors.
group Programming parameters
This group is available for some types of devices. It contains settings of which device parts or
areas has to be programmed.
group Erase parameters
This group is available for some types of devices. It contains special settings of erase modes
of selected device.
Device / Device options / Serialization
Serialization is special mode of program. When a serialization mode is activated, a specified
value is automatically inserted on predefined address into buffer before programming each
device. When more devices are programmed one by one, the serial number value is changed
for each device automatically and inserted into buffer before programming device, so each
device has unique serial number.
There are three types of serialization:
? Incremental mode
? From file mode
? Custom generator mode
Dialog Serialization contains also settings for associated serialization position files that are
used with project files with serialization turned on. For more detailed information about using
serialization in project files, look at Serialization and projects.
Basic rules of serialization:
If a new device is selected, the serialization function is set to a default state i.e. disabled.
Actual serialization settings for actually selected device are saving to disk along with
associated device by File / Exit and save command.
72
发布紧急采购，3分钟左右您将得到回复。
相关PDF资料
84702-0008
CONN RECEPT ETHERNET 8-8 PNL MNT
848A
MEMORY PROGRAMMER PARALLEL INTER
85506-0001
CONN MOD JACK VERT 8-8 HI-SPEED
85507-0001
CONN MOD JACK VERT 8-8 SHIELDED
85508-0001
CONN MOD JACK VERT 8-8 SHIELDED
85508-5001
CONN MOD JACK 8POS T/H HI SPEED
85511-0001
CONN MOD JACK VERT 8-8 HI-SPEED
862015-1
6 POS RECEPTACLE
相关代理商/技术参数
845
功能描述:程序设计器 - 基于通用和内存 REORD 615-865 UNIV. WITH SOFTWARE
RoHS:否 制造商:Xeltek 产品:Universal Device Programmers 工具用于评估:EPROM, Parallel/Serial EEPROM, FPGA, PROM, Flash, BPROM, MCUs, PLD Devices 接口类型:Parallel, USB 工作电源电压:90 VAC to 250 VAC
845 1 1/2"X15YD
功能描述:SCOTCH BOOK TAPE 845 1-1/2 IN X 制造商:3m 系列:* 零件状态:在售 标准包装:24
845 3"X15YD
功能描述:SCOTCH BOOK TAPE 845 3 IN X 15 Y 制造商:3m 系列:* 零件状态:在售 标准包装:12
845 4"X15YD
功能描述:SCOTCH BOOK TAPE 845 4 IN X 15 Y 制造商:3m 系列:* 零件状态:在售 标准包装:8
845 PRO4
制造商:Micro-Star International 功能描述:845 P4 S478 SDRAM LAN - Bulk
845 PRO4-L
制造商:Micro-Star International 功能描述:845 P4 SKT478 ATX SDRAM - Bulk
845 ULTRA
制造商:Micro-Star International 功能描述:845 SKT-478 P4 DDR ATX AUD - Bulk
845 ULTRA-DF
制造商:Micro-Star International 功能描述:845 SKT-478 P4 DDR ATX AUD - Bulk